Pontoon Boat Plans Aluminum | Daggerboard planing rudder blank transom re enforcement Oar Prototype 1

Pontoon Boat Plans Aluminum

Well, a busy frenetic post. Lots of small items got done over the past few days on my Goat Island Skiff.

Daggerboard planing:

The daggerboard needed to get smoothed out. It was a lumpy mess.


I didnt know whether to hit it with the orbital sander or my hand plane. I really just want to feed it through a real machine plane since I need to lose 2mm off the blank, but maybe Ill do that by hand... (?) However, in the end I got a roughly smoothed out daggerboard using my hand planes. It was not as tortuous as I thought it would be, and it all worked out pretty good in the end.


Rudder blank:

I also needed to get my rudder glued up. Initially this had not occured along the daggerboard due to the lack of appropriate timber, I had used my supply dedicated to the blades for the daggerboard mostly. However, I did have a lump of cedar left over from the stem. I had forgotten about this one. It took a few minutes of brainstorming, a couple of swipes on the table saw, and in no time I had my blank, and it was glued up on underneath the ubiquitous heat tent in my 45 deg. F garage.


A different wood pattern than the daggerboard, but that is OK by this amateur!

Transom:

Then it came to my attention that my transom was not backed up enough for the rudder. The intrepid reader will remember when I put the backing to the rudder gudgeons on the transom. It was a sticky mess. WELL I should have looked at Duckworks first and checked out the dimensions of the equipment I was going to use. Then, I could have fitted an appropriate backing. I did not. My backing was far too inadequate, so today I added sides to it for a 6" width, and then sandwiched on another solid layer on top.



The brick weighs it all down.

Finally, how in tarnation am I going to propel this boat when there is no wind? By oar!

Oars-- Oar Prototype #1:

My oarlocks, sockets, and another hatch came in the mail yesterday.

YAY MAIL!

The oarlocks are beautiful. I got two pairs of sockets, one for the gunwales, and another pair so I could have a socket on the transom, in case I lose an oarlock or oar, I can still yuloh my way to shore and safety. Search yuloh.

This also means it was time to try my hand at oar-making, which interested my lovely wife.

Jim Michalak offers us some oar plans in his book, Boatbuilding for Beginners, and I used those. Storer also has free oar plans available, but Michalaks were simpler, and I decided to mix and match a little bit. No problems, right? Haha.

My oars for the GIS should be about 9. Technically, 92", which is what we used. I bought two cheap pieces of pine lumber to make my oars, 10 long each. Each board will offer up all three layers for the laminate construction of this oar. The plans call for oars that are 6 11" long. We extended these oars 23" (27") by using a formula at Shaw and Tenny oar-makers extra-ordinaire.

58" (width lock to lock) / .5 = 29 + 3 = 31" of inboard length.

The grip on these plans are 5" long and the inboard portion of the loom is 16", so we added 10" to make it 26" + 5" = 31"

The remainder of the 27" was 17" and we added this to the outboard section of the loom.

Then, off to map the stations, trace and cut.

After some deliberation I decided to cut the entire oar, all three blanks, by hand. So away I ripped with my Japanese handsaw. It was more accurate than the jigsaw, and quieter. The table saw would have been a sweat-fest. Here we are, half-way through one side of the main blank:


Then, with 4" to go on the last laminate side, a eye-knot snapped, and sent the last 6" of one of the laminates that attached to the blade soaring into the garage. BOO. I had just ripped 20 feet of board by hand, and the last 6" decided to let go.


So I decided that this end was going to get the shaft (haha) and it was going to be a little short. Prototype #1, right?

I did a mini-scarf by cutting right on through the two pieces, eliminated the knot, using the method illustrated below:


Then, off to the basement for the gluing!



Do you find information about Pontoon Boat Plans Aluminum are you looking for? If not, below may help you find more information about the Pontoon Boat Plans Aluminum. Thank you for visiting, have a great day.

Read More..

Dinghy Boat Plans | West Marine Thieving Scumbags

Dinghy Boat Plans

I ordered some small parts (gudgeons for my rudder) for my boat from West Marine.

I received an email stating that the items have shipped.

I received an invoice in the mail stating the items have shipped.

After 10 days I called, looking for my parts.  "Theyre coming."

After 20 days, I called, looking for my parts.  "Call back next week."

I call back today, and they tell me that the items have not shipped.  They dont even have the items in stock.  There is no timeframe available when the items may be in stock.

They have my money, and I dont have any parts.  Need to find alternative plans now.

Do you find information about Dinghy Boat Plans are you looking for? If not, below may help you find more information about the Dinghy Boat Plans. Thank you for visiting, have a great day.

Read More..

Boat Plans Nz | Rudder design 4 daggerboard glassing

Boat Plans Nz

After many trips to the hardware store getting stainless steel carriage bolts and machine screws that were often the wrong size, I finally got my rudder box together in some sort of usable fashion.  As my intrepid readers may remember in three other previous posts (search in the month of March), I have been trying to figure something out in order to get my tiller to be detachable.  I went with the final option, illustrated in this post. 

The rudder box is glued up but not glued together.

As you can see, I am wearing my camo Converse sneakers.  Very cool.  The original tiller design calls for the tiller to be permanently attached to the top of the box, where my shortened tiller stock is now-- so originally that would be much longer, but permanent.  This way, I can remove the tiller and leave the rudder in the water, freeing up open space in the boat during quiet times.  I used a carriage bolt with a butterfly nut tensioned by a split washer.  Dont drop it, and carry a spare! 

The spacer is as of now temporary, but I could do one of three things.  I could lengthen the spacer to make it full-tiller length, giving the tiller laminate strength; I could shorten the spacer; I could make two evenly spaced spacers, I could leave it the way it is.  This is yet to be determined.  Heres a closeup for the interested:

Im having some serious problems with my hardware for the rudder, unfortunately.  I wanted a pintle and gudgeon style assembly, but my 1.5" gudgeons are not fitting around my rudder box, even though its 1.5" wide.  Something aint right.  Also, Id have to expand my tiller access hole in the transom to accommodate the up and down motion to get the rudder in and and out.  So Im scraping the pintle/gudgeon idea and Im going to go with the gudgeon/gudgeon idea, as the original plans stipulate.  Which means I have to find some sort of long pin to thread between all of them.  Boo to that. 

Also today Ive been working on my blades.  My rudder got sanded down to the matte finish, and I carefully taped off vertical areas that would run, and applied one last thin coat of epoxy onto one side of the rudder.  Tomorrow, the other side.  I used a plastic spreader, and it went very well, very smooth, and Im very happy with my luscious result:

Youll notice on the left hand side that the leading edge still isnt coated, this was taped off earlier.

Then, off to glassing my daggerboard!  Much like the same for the rudder, except I cut a bigger piece.  I had a lot of runs in my rudder, and I figured this time I would lay the board flat, spread epoxy with a squeegee, and then turn it over, do the other side, and then hang it up. 

So I went ahead and did one side horizontally:

 I thought I was being pretty smart. 

So then I turned it over and did the other side.  Something caught my attention and I looked underneath my board and...

... well I didnt take any pictures because needless to say the whole first side has very neatly peeled away from the board, thanks to Mr. Theory-of-Gravity.  Gravity is only a theory by the way, they should teach both sides in schools so kids know this, because there is lots of evidence that gravity does not exist, but "they" dont want to show you it.  I digress.  Today, gravity was obviously working quite well.  I finished the job at hand, and then hung it up, and re-spread the cloth down.  Fortunately not much damage done, but for my smartness, well, not so smart now.  Here it is all hung up to dry:

Its late, Im still periodically coating the board to get the weave filled, and Im tired.  I timed this one bad.

Thanks for reading!



Do you find information about Boat Plans Nz are you looking for? If not, below may help you find more information about the Boat Plans Nz. Thank you for visiting, have a great day.

Read More..

Yacht Boat Plans | A better post for a new month!

Yacht Boat Plans

The below was a crummy post for the first of June!  Heres to a better start to the first month of summer:

This is a Luna moth I found at a gas station fluttering uselessly against the lights.  I jumped out of the car and took off my shirt and chased it around the station until I caught it and brought it home (much to the amusement of my wife).  A beautiful specimen of a Giant Silk Moth (approx. 6" wingspan).  This one is a male, you can tell because it has well developed antennae.  It lives for about a week and does not eat, it lives only to mate.  I found a Polyphemus last year on Nantucket, but lost the pictures... boo.  But this is beautiful, my first one.  Another good way to start the summer! 

Do you find information about Yacht Boat Plans are you looking for? If not, below may help you find more information about the Yacht Boat Plans. Thank you for visiting, have a great day.

Read More..

Boat Plans Catamaran | Fiberglass Tape epoxy encapsulation

Boat Plans Catamaran

Yesterday was a bomber of a day.  Total Goat Island Skiff immersion.  Well over 14 hours of spanking.

Basically, I want to float test this boat.  My pond, frozen with several feet of New Hampshire ice iced out overnight.  I woke up two mornings ago to find that the ice cap had literally disappeared, and the boat was not ready.  So the hustle began.

First, I planed to fit a 3/8" poplar dowel for the the bow.  I scratched up the epoxy on the bow, scratched up the dowel, and stuck it on.  This will be glassed over with fiberglass tape.

I held it on with painters tape.

Then, off to the races.  Taping the chines with fiberglass tape (FT) is easy, and kind of rewarding.  First, I measured the tape to fit the chine, and cut it off.  Then I slopped on some unthickened epoxy along the chine, and placed the tape along it, dabbing it down to hold it in place.  This tape has a "selvage" edge to it, which according to the plans should be removed.  Basically, its a plastic string that holds the fabric together, but its a real pain in the ass to sand down, or so I am told.  It came out really smooth on the fiberglass I used for the blades, but on this FT it just mocked me incessantly.  So I said "screw it!" and glued it down with the edge on the bottom.  In case I couldnt sand it down at least it would partly hidden.  After the tape is laid down in position, I slopped on epoxy to wet it out and get it to stick.  Work from the middle to the ends of the boat.  Some gentle tugging got it in a good straight line and evenly over the rounded chine (round with a few passes of a plane and hit it with the sander).

 I did this to both sides, and the bottom/transom joint.  Im not sure if the side/transom joint needs to be done or not, and I can always do that later.  The bow will be glassed when the epoxy has cured on the dowel and I can fair it to the hull.

After that came the fun fun job of spreading the epoxy on the bottom and the sides.  I did the bottom first while I debated how to do the sides.

 I did not pre-coat my panels because A: I wanted to see my boat! and B: I wanted to ensure the most effective gluing surfaces and I did not feel like taping their positions off.

In retrospect, the bottom was very easy, the sides a little more work.  I would suggest that any builder at the very least, pre-coat the outside side of the sides for simplicities sake.  Pouring the epoxy onto the sides and spreading it around was a little more of a challenge on the vertical surface, but due diligence paid off for a pretty neat job.

Back to that selvage edge.  After the epoxy had cured a bit on the glass, I decided to grab my utility knife and see if I could cut it off!  I could, and it worked awesome.  Pulling it out first before glassing would have been preferred, but this was the next best thing.  Holding the blade close to the edge I was able to get a nice clean cut down the the length of the hull, and then all I had to do was pull it up.

Presto!  As you may notice you can still see the weave in the FT.  This weave took a lot more work to fill in than the glass on the blades.  On the suggestion of my compatriot in Sacramento, I threw on two coats of slightly thickened epoxy and it filled it in much better than the straight undiluted stuff.

Heres a before and after:

A long day, but worth it.  A float test is quickly looming in my future!


 

Do you find information about Boat Plans Catamaran are you looking for? If not, below may help you find more information about the Boat Plans Catamaran. Thank you for visiting, have a great day.

Read More..

Boat Plans For A Chesapeake Deadrise | Daggerboard trunk glued up and rear seat glued on

Boat Plans For A Chesapeake Deadrise

Ok my patient mates, heres some photographic evidence of my work on the boat last week before I left for self-imposed exile at work.

First, I finally got that bedamned daggerboard trunk glued up.  Somehow, I wasnt forward thinking enough, and I glassed up the daggerboard without really giving much thought to how it fit in the already made trunk.  Well, I did but discounted further planing on of the daggerboard and decided that I was done with all the planing and sanding thank-you-very-much and whatever I had, I had.

This was most unfortunate, because I few more minutes of planing would have produced a superior quality board, and it would have fit in my daggerboard case.  So then I was stuck with the project of widening my case, but only by 2-3mm at most because really, all I needed was 1-2mm.

Fortunately, I found 3mm Okoume marine plywood at Goose Bay Lumber, and cut it to fit over the framing for the trunk.  This widened the trunk appropriately.  Here is the widening sequence in pictures:

Very self-explanatory, I think.

Next, I still struggle with the hardward issues for the rudder and transom gudgeons.  I dont know how Im going to get this rudder assembly attached to the boat.  The problem is that the hole to accomodate the tiller does not have the vertical clearance required to use a gudgeon-pintle scheme, which is by far the most convenient.  I toyed around with it and thought about enlarging my tiller-hole, but my pintle arms didnt fit around the rudder cassette.  A second order of larger, more heavy-duty gudgeons for rudder and transom fit great, except not with each other, and the arms were too long for the spacer in the cassette... A rod pushed through the gudgeons would not have fit cleanly and I would have had a clunky feeling rudder, the round peg in an oval opening thing, if you can visualize that.  So I still sit, wondering how I will fix this conundrum.  Many people have done it successfully, but Im still hunting around for the best hardware.

Because of all this drama, I have delayed gluing on the rear seat.  I got tired of having it loose, and glued it on before I left.  Here, yet again, is my "Forest of Bricks" holding it all down.

And the gratuitous parting shot:

Do you find information about Boat Plans For A Chesapeake Deadrise are you looking for? If not, below may help you find more information about the Boat Plans For A Chesapeake Deadrise. Thank you for visiting, have a great day.

Read More..

Plywood Boat Plans Australia | Bottom trimmed centerboard trunk and bat house!

Plywood Boat Plans Australia

Today was a productive day, the boat went upside down and back again.



My friend Peter ambled over with his router. This, combined with a flush-trim bit for the router, is a fabulous tool at dissolving the extra overlap left over from the over-sized bottom. It was either going to be a hackfest at sawing/planing it off, or this. The router was mucho easy to use, I cleaned up the enter boat in mere minutes. It left a little lip, which was cleaned up by my handplanes. Long strokes parallel to the boat to get it close, and then the smaller block plane held at an angle to the hull to get it finally flush. This took longer but was enjoyable work. The boat got dropped once, and it was not any worse for the wear.

The centerboard trunk components are also all glued up, but in two pieces. They will not be glued together until the daggerboard is complete, and then I can appropriately take the down the spacers inside (made from daggerboard jetsam, hence same width pre-finishing) to match the daggerboard, plus 2mm for a cozy fit. The daggerboard is being worked on on the side... I think I have a tempestuous relationship with the board and Im taking it slowly.


Peter, while he was over, made a three chambered bat house for his own house. Hes hoping to attract a small colony of bats to summer with him in his moist woods. One brown bat will eat 500-1000 mosquitoes an hour (yes, read that again) and a large bat house could contain tens upon tens of bats if not well over a hundred. Thats a lot of mosquitoes that are going to bite the dust. Additionally, bats eat truckloads of insects that attack farmed crops, help in seed dispersal and some species can be key in plant pollination. Bats do not equal gross, bats equal important. In New England (and spreading south!) we are afflicted with "White nose syndrome" which is hacking away at our bat population. The more bats we get, the better off we all are.

Each chamber is 3/4 of an inch. There will be a plastic grated landing zone below the chambers. The box will be painted a dark brown, and affixed on his house. They like it hot, and hot it will get. Bring on the bats!

Do you find information about Plywood Boat Plans Australia are you looking for? If not, below may help you find more information about the Plywood Boat Plans Australia. Thank you for visiting, have a great day.

Read More..

Boat Plans Canada | Float Test

Boat Plans Canada

I couldnt take it anymore.  How would my ship, my Goat Island Skiff, my beauty, my instrument of adventure to wonderful and distant and nebulous ends sit on her lines?  Would she list, be bow heavy, stern heavy?  There were some things in the construction of her that didnt match the plans, some bevels, some shapes, some angles, and I was worried that in the water she would sit funny, maybe bow down a bit, instead of the beautiful plumb bow sitting upright!

My pond at my parents-in-law iced out rapidly last week, which motivated me to tape the chines and slap some epoxy on the sides of the hull.  Yesterday, it rained hard.  Today, we woke up at 7, and there was no rain, but wind, and 32*F/O*C.  Snow flurries on the horizon to the west.  My lovely wife ready to rock.  It was time.

Wind was blowing about a Force 5 on the Beaufort scale, around 20kts or so.  With ice-out just a few days ago, the water temperature wasnt much higher than the air temperature.

It was now, or another nail-biting day.  It was time.  A kiss on the breasthook, a quick murmur to her... "Please sit straight on your lines..." and with a heave, and a ho, she was in the water.

Not a maiden voyage, not a christening, nothing but a quick test.  She will get all the formalities and Poseidon will get all his tributes when she is worthy.  Just a float test... but exciting all the same.

...and DAMN if she doesnt look straight!

Do you find information about Boat Plans Canada are you looking for? If not, below may help you find more information about the Boat Plans Canada. Thank you for visiting, have a great day.

Read More..