Boat Plans Nz | Rudder design 4 daggerboard glassing

Boat Plans Nz

After many trips to the hardware store getting stainless steel carriage bolts and machine screws that were often the wrong size, I finally got my rudder box together in some sort of usable fashion.  As my intrepid readers may remember in three other previous posts (search in the month of March), I have been trying to figure something out in order to get my tiller to be detachable.  I went with the final option, illustrated in this post. 

The rudder box is glued up but not glued together.

As you can see, I am wearing my camo Converse sneakers.  Very cool.  The original tiller design calls for the tiller to be permanently attached to the top of the box, where my shortened tiller stock is now-- so originally that would be much longer, but permanent.  This way, I can remove the tiller and leave the rudder in the water, freeing up open space in the boat during quiet times.  I used a carriage bolt with a butterfly nut tensioned by a split washer.  Dont drop it, and carry a spare! 

The spacer is as of now temporary, but I could do one of three things.  I could lengthen the spacer to make it full-tiller length, giving the tiller laminate strength; I could shorten the spacer; I could make two evenly spaced spacers, I could leave it the way it is.  This is yet to be determined.  Heres a closeup for the interested:

Im having some serious problems with my hardware for the rudder, unfortunately.  I wanted a pintle and gudgeon style assembly, but my 1.5" gudgeons are not fitting around my rudder box, even though its 1.5" wide.  Something aint right.  Also, Id have to expand my tiller access hole in the transom to accommodate the up and down motion to get the rudder in and and out.  So Im scraping the pintle/gudgeon idea and Im going to go with the gudgeon/gudgeon idea, as the original plans stipulate.  Which means I have to find some sort of long pin to thread between all of them.  Boo to that. 

Also today Ive been working on my blades.  My rudder got sanded down to the matte finish, and I carefully taped off vertical areas that would run, and applied one last thin coat of epoxy onto one side of the rudder.  Tomorrow, the other side.  I used a plastic spreader, and it went very well, very smooth, and Im very happy with my luscious result:

Youll notice on the left hand side that the leading edge still isnt coated, this was taped off earlier.

Then, off to glassing my daggerboard!  Much like the same for the rudder, except I cut a bigger piece.  I had a lot of runs in my rudder, and I figured this time I would lay the board flat, spread epoxy with a squeegee, and then turn it over, do the other side, and then hang it up. 

So I went ahead and did one side horizontally:

 I thought I was being pretty smart. 

So then I turned it over and did the other side.  Something caught my attention and I looked underneath my board and...

... well I didnt take any pictures because needless to say the whole first side has very neatly peeled away from the board, thanks to Mr. Theory-of-Gravity.  Gravity is only a theory by the way, they should teach both sides in schools so kids know this, because there is lots of evidence that gravity does not exist, but "they" dont want to show you it.  I digress.  Today, gravity was obviously working quite well.  I finished the job at hand, and then hung it up, and re-spread the cloth down.  Fortunately not much damage done, but for my smartness, well, not so smart now.  Here it is all hung up to dry:

Its late, Im still periodically coating the board to get the weave filled, and Im tired.  I timed this one bad.

Thanks for reading!



Do you find information about Boat Plans Nz are you looking for? If not, below may help you find more information about the Boat Plans Nz. Thank you for visiting, have a great day.

Read More..

Boat Plans Wooden | New post!

Boat Plans Wooden

With nothing in it!

Work on the Goat Island Skiff has been temporarily stopped due to a return to work/on the road status.

I have pictures of some work I did just before I left, but they are unfortunately inaccessible at this point in time.  Stay tuned until next week!

Do you find information about Boat Plans Wooden are you looking for? If not, below may help you find more information about the Boat Plans Wooden. Thank you for visiting, have a great day.

Read More..

Boat Plans Arch Davis | Rudder stock design rudder 2 daggerboard shaping

Boat Plans Arch Davis

WELL

Informative day today as I peddled my rudder stock idea over at Mr. Storers forum.

There was enough persuasion action going to keep me going with the plans in term of a backless rudder stock with a daggerboard rudder.  However, I really want to be able to ditch the tiller and leave the rudder installed on the transom.

I came up with this idea:

In this plan, the rudder stock stays exactly as the plans stipulate, except I add on 15mm at the top.  This provides an area to attach a cleat (blue).  Then theres another below it (blue) and the tiller-- which is two pieced-- cradles the rudder stock.  Bolts run through the cleats into the spacer, and the tiller which slides between the cleats is held in place with a pin.

Storer warns that the torsional forces on the tiller could tear it apart, Im hoping that between the three cleats bolted through the spacer, and a bolt higher up on the tiller (not shown) to keep it together, I should be ok.  Time will tell.  I am almost positive this is the model Im going with, unless I get overwhelming evidence otherwise.

In other news, I finished rough shaping the rudder and daggerboard. 

Nice.

Do you find information about Boat Plans Arch Davis are you looking for? If not, below may help you find more information about the Boat Plans Arch Davis. Thank you for visiting, have a great day.

Read More..

Boat Plans Australia | Mast in boat re epoxy ing and neat turtles

Boat Plans Australia

So, Ive been pre-occupied recently with other events, namely, my impending return to work after some serious back-rehab (phys. therapists = good), some life events, and so on and so forth.  So, this is good.  Im broke, my back is better (which means I can actually do some work in the hull as opposed to just staring at the bottom of the boat), and springtime is coming.

One harbinger of spring is the emergence of turtles through their long torpor and into the light once again.  Today I ran into this chap, a Blandings Turtle which is actually considered endangered in New Hampshire.  They dont mate until their late teens, and they can live to around 80.  Anyway, I moved this guy for a photo-op only to later find out theyre endangered in NH, so I feel like an ass, but I treated him gently and placed him back right back where I found him.  Actually, this could be a her, I should find out.  Handsome, regardless:

 

I will report this to the Dept. of Fish and Game, they keep track of this stuff.  I also reported a Bobcat that came trundling through my yard two days ago.  That, was neat, but it was too quick and I have no photo.  Sorry.

ON TO THE YACHT!

With the mast all built, I tapered the base per the plans.  If you remember, I made the mast slightly larger than the plans called for, not much, just 1mm here and there, but it affected the fit in the mast partner and step, and those had to be enlarged.  This was not a big deal, its only a little bit and if you may recall, intrepid reader, I made the stock of the partner and step bigger than called for.  So I feel safe doing this.  Here is my great friend Matt, recently returned from Overseas Adventures Extra-Ordinaire doing his duty, and helping me out at the annoying task of rasping the mast partner larger.  Welcome home:

He did a most fantastic job.  Then I ruined it.

After some rasping and Dremel-ing the heck out of the mast step, we got the mast stepped:

I offer you many vantage points.  The overhead is kind of neat.

The mast is currently being fiberglass-taped right now, two tapes at the base, two at the top, and two amidships, one covering the single knot in the lumber.

Also being worked on is the hull.  I sanded the epoxy coating I gave it the other day, and added a third coat.  This was a technique I stumbled upon doing my BHs.  If I sanded and then added a last coat, it came out super smooth.  Im hoping for the same with the hull, especially since the Im trying to get the fiberglass tape down smooth.  After aggressive sanding, Im thinking the extra coat will fill up to the gap.  Here she is, sanded:

So next up, I have to figure out the rudder hardware problem.  This is worthy of another post.  I cannot, for the life of me, get my rudder hardware figured out, and its beginning to piss me off.  By hardware I mean what attaches the rudder stock to the transom.  Some gudgeons are too small, others are too big, Im going nuts.  Also, I have to figure out what to do with my daggerboard trunk.  It needs to be, literally 1mm wider, and I dont know how to do that.  A lot of glue, maybe? when I glue it together?  These are two items that are holding me up.  Also, I have to epxoy coat the inside of the boat, with nice weather finally on its way, there shouldnt be a hold-up.  I really want the hull ready for paint when and if I get some time off from work to come back home.  If Im home for 24 hours, I want to be able to get mucho stuff done.  So that is what Im staging for right now.

Do you find information about Boat Plans Australia are you looking for? If not, below may help you find more information about the Boat Plans Australia. Thank you for visiting, have a great day.

Read More..

Wooden Boat Plans Australia | Designing new rudder stock 1

Wooden Boat Plans Australia

Im trying to build a swing-up rudder stock design for my Goat Island Skiff, similar to the one I have on my Laser, except wood, and fitted for the GIS rudder.  The original plans call for a daggerboard style rudder stock where the rudder is removed vertically through the box, and the tiller is permanently attached to the box.  See here.  I am not a big fan of this design, though I appreciate its simplicity.

Here is why:

1.  I do not want a permanently attached tiller to the rudder stock.  I would like to be able to remove the tiller, and leave the rudder in the water, or at least raised but still attached to the transom.

2.  I do not like the bungee cord design to the hold the rudder in place

3. I want to use pintles and gudgeons, which would be difficult with a permanently attached tiller and dropping the assembly into place.

Here is a quick mock-up of a slightly enlarged rudder box per the plans, with a rudimentary rounded rudder top for swingability.

The stock has been extended 3 cm aft, and 1 cm down.  I am limited by the size of the transom and the location of the hole to accept the tiller in the transom.  The tiller would run between the two side of the stock across the top of the rudder and be fastened with a pin.  The spacer in the front of the box would be the same called for in the plans.  The exterior of the stock would have the two re-enforced areas per the plans, running across the top and bottom, and in addition a third re-enforced area to support the axle.  I will probably also trim the leading and trailing edges of the top section of the rudder in the box area to get a good climb out of the water as well as keep it from dragging along the beach.

Thoughts?

Do you find information about Wooden Boat Plans Australia are you looking for? If not, below may help you find more information about the Wooden Boat Plans Australia. Thank you for visiting, have a great day.

Read More..

Boat Plans Aluminium Australia | Rudder stock design 4 Mast gluing

Boat Plans Aluminium Australia

In yet another installment of "I try to re-design the rudder stock" I have received yet another set of plans from a Goat Island Skiff builder in New York.  He has graciously supplied me with these two schematics of his own design, as a solution to removing the tiller from the rudder assembly without having to take the rudder off the transom.  It is self-explanatory:

I really like this design, it is better than mine for two reasons:  1. It maintains Mr. Storers rudder stock design and hopefully solves the structural issue that he was concerned about, 2. There is less time fiddling over the transom pulling very critical pins over water of yet-to-be-determined depth, if you get my drift.  I can remove the tiller from the safety of the cabin.  Unfortunately, I will still have a stub of tiller sticking into my domain, but I think, for now, this is the idea Im going to go with.  The great thing about the rudder stock is that it is simple and easy to construct, I can always make another.

In other news, the mast was glued in its first step today.  In the previous post, I shaped the narrow staves.  This was a workout, but I worked carefully, and Im happy with the result.  Then, off to make the spacers for the ladder frame.  I used a piece of fir that was lounging around the garage, some stud material.  I used some good parts, and cut them to fit.  The base plug meant a trip to Lowes.  This is the first wood part of the boat that was not bought at either of my two local lumber stores.  Sorry guys.  Anyway, an 8 piece of 4x4 cedar.  I thought about using fir, for a few bucks less, but I went with the rot-resistant cedar.  Its an important piece, its light, and it should be good.  The other spacers Ill goo up with epoxy and make them plastic.

Well, that was interesting how the photos lined up, but I like it!  Notice the base plug.  After a quick mock-up my lovely wife and I took one of the uncut stave stock pieces and brought it into the basement, where I can get an even floor workspace and a slightly higher temperature, better for quicker gluing.  We made sure that we could get the wood in and out of the basement two different ways, so I dont build the mast and then get it out.  I am positive I can get the mast out of the basement.

Layed out ready for the dry fit:

Sweet, I did it again, but I dont know how.  The mast is quite straight, but I decided to use one of the wide uncut staves as a backbone for gluing, that way I could ensure that the mast is straight with no wobbles.  It also gives me a good even workspace for gluing too.  I covered one stave with packing tape, and glued away:  Notice too, the hardwood runners that will be glued to the bottom of the hull, they are long ones and needed to be scarfed.

It went well.  The bricks are slightly nudging the mast into a straight position.  Youll also notice that you dont see much of the wide stave underneath this glue-up, thats because the tolerances are super tight.  I overcut my narrow staves by 1mm and it pretty much ate up all the space on the wide stave.  I briefly considered re-planing the staves, re-working the spacers, and then gluing, but my lovely wife stopped me with some business graduate degree mumbo-jumbo stuff and talked me out of it.  I might have to plane a little extra off the base to get it to fit in the mast step, and I can (with difficulty) enlarge the mast step as well if need be.

Tomorrow, gluing the wide staves and completing the box.
 

Do you find information about Boat Plans Aluminium Australia are you looking for? If not, below may help you find more information about the Boat Plans Aluminium Australia. Thank you for visiting, have a great day.

Read More..