Boat Plans Bruce Roberts
YO.
Today I glued on the front seat. I also epoxy sealed the rear watertight compartment.
Im just going to let you know that today was the most productive, least disastrous, most efficient gluing event yet on this boat. Still some mistakes, but NOTHING like gluing the boat together or putting them bottom on. Which makes me worried that I screwed up or was deficient on the most important parts of building, but alas, what I have, I have, and well see if she sinks or swims. Hopefully, she soars.
Anyway.
When I realized that the garage was holding steady at 44 deg. F (7 C) I decided to get with some gluing. I mixed up about 3 pumps of resin and the corresponding hardener and dumped in a bunch of thickener, and applied it to my pre-coated seat cleats and BH1 + 2.
I just really dumped the thickener into the mix. I figure this: If I have a tight fit, less silica, if I have a loose fit, more silica for a more filling mix. It took me this long to figure it out. This, with some valuable information from the Storer forum has helped me make better epoxy mixes. One rule to follow: Pulling the mixing stick out of the glue, if the point droops, its good for gluing, if the point stands tall, its good for filleting. Variations apply to temperatures, however, as you will soon find out.
After I applied the glue, I realized it was stiffening up because of the cold temps in the garage. This is not conducive to smearing and filling holes. I grabbed a hair dryer and tried to warm it up the best I could. Using this information that is stiffens, I kept my fillet mix a little thinner than the point "standing tall." I applied the seat and it dropped right in nice and tight. I threw some bricks on it to weigh it down, and took a few pictures from inside the compartment to see how I was faring with the glue. Here, were looking towards the bow:
As you can see, good squeezage on the middle cleat, not so good up around the bow. I added some bricks. I DID have good squeezage from the sides of the seat upwards, so I know I have good contact. Im not bothered I dont have excess spilling off the side of the cleat. Next up was some fillet work. I was using a squeegee and then a PLASTIC SPOON that did absolute wonders to throw down a sweet sweet fillet. Nice and clean. I kind of eyeballed what looked good to me, and this was the result:
I think thats sufficient. Heres the forward seat glued in position with the forest of bricks:
Im pretty happy with the result. However, after I was done I wandered into the kitchen where my beautiful wife asked me what I did.
Wife: So howd it go?
Me: Oh it went great, Im the man, Im the next Herreshoff, I glued on the front seat. I am The Man.
Wife: Great! Youre great. Im so glad I married you! Thats the watertight compartment, right?
Me: Yup! The seat forms the forward watertight compartment!
Then I wandered downstairs to get a beer and realized... Son of a GUN... Do I have any gaps between the plywood seat and BH1 that forms that watertight compartment? OH NO! Look at this picture again, pay attention to BH1 starboard side and glue amounts:
Now look at this picture snapped from within the mast-well between BH1 and 2 looking forward on the starboard side!
Gaps! And while I dont think they run through, there are photodocumented gaps on the inside of the tank as well. Dammit.
Im too tired and whooped to worry about it tonight, I will make sure to squeeze some epoxy in there in the future. Its also a strange spot to get to, I have to get into the boat to make this one work, and shes up on buckets, so it will have to wait.
Thank you, wife.
OH YEAH, heres my heater tent. I can keep it 56 F (13 C) in there with my little space heater.
Do you find information about Boat Plans Bruce Roberts are you looking for? If not, below may help you find more information about the Boat Plans Bruce Roberts. Thank you for visiting, have a great day.
0 komentar:
Posting Komentar